No.26 Mind the Gap

A change of scenery, well a change from running trains.  There has been a gap between the two baseboards ever since the layout was started and it was time to block up the opening:





I wanted an arched retaining wall.  Time and economy are important and I favour the use of card kits.  In this instance I decided to make the wall using parts from the Metcalfe Two track Viaduct Kit (PO241).



The first task was to form the arches.  The picture above shows how parts of the internal viaduct supports from the kit were used to shape and form the internal arch walls.  The underside of the arch ring being cut from the ‘brick’ paper provided with the kit.


More by good luck, than by design, I found that the height between my platform and the underside of the upper baseboard was almost exactly the height of the top part of the arches from the kit.   Time then for a dry run:

Once I had established that everything was going to fit the arch parts of the walls were glued top and bottom and pushed in place between the upper board and the platform.  It was then a relatively quick job to stick the facings to the arches and to glue the top brick wall in place.  The ‘devil’ was then in the detail.

Metcalfe recommend ‘impact’ adhesive.  I find such glue messy and instead use PVA.

At the end of the platform the arches had to be carried down to the top of the lower baseboard.  I also needed to fabricate a ‘third’ arch.  The Metcalfe kit assumes that the arches will be made up two at a time.  The length of wall needed here meant that I would have to make a single arch.  I must have been losing concentration because it took three attempts to get the heights of adjacent arches to match each other whilst at the same time remaining vertical. (I am sure you will be familiar with the situation where baseboards are not quite as level as first imagined.)  Finally this end of the wall was finished with a shorter plain section of wall with a triangular tapered section to connect up to the approach embankment.



There was then the small matter of what to do under the girder bridge at the opposite end.  Waste not want not.  I was able to reuse the two arches previously discarded for being the wrong height.  These were glued in place, beneath the bridge, around a dummy pillar to give some semblance of support for the overlying bridge structure.


Finally a general shot of the finished wall.

Location: Dumfries and Galloway, UK

Comments

Post a Comment

Popular posts from this blog

No.123 Chocolate and Cream and BR1s – the Replica Railways Restaurant Buffet

Image
This Post describes some modifications that I have made to a Replica Railways BR Mk1 RB. Previously i have modified the Mainline Maroon RB by fitting Finecast glazing, wire handrails and Bachmann close coupling mechanisms. I promised myself that I would do the same for the chocolate and cream Replica BR(WR) RB. Success! Replica Railways BR(WR) Restaurant Buffet on BR1 Bogies First task - find a suitable coach! Replica Railways Mk1 RB from around 1992 Models are bit like London buses. When I first started looking for a BR(WR) RB there didn’t seem to be any around and eventually my coach came from Australia. Then suddenly there were lots available here in the UK. On opening the box I was surprised to discover that Replica had painted the solebars chocolate to match the lower body panels – why? Was someone confused by the blue solebars ion the blue and grey version? They should be black and they can be over painted with new transfers added from the P...
Read more

No.98 The Peco Streamline 3 Way Point.

Image
The Peco Streamline 3 Way point is an extremely useful space saving device. This Post is prompted because I had to sort out a couple of problems with the installation of my own three way point. I was also aware that other modellers   were finding difficulties with the operation and installation of their 3 way points. The design of the point is symmetrical and has the appearance of a LH point being placed directly on top of a RH point. As a consequence the construction of the point is quite complex and the point requires careful handling especially during installation. When first marketed by Peco the point was only available with ‘Insulfrog’.  The view below shows my first ‘Insulfrog’ point but reinstalled on my second layout. Peco Code 100 3 Way Insulfrog Point – the Park View Layout 1990s The big advantage of the ‘Insulfrog’ point is that it does not require any separate electrical switching and hence is suitable for manual or simple mechanical operation. My...
Read more

No. 152 Remotoring a Hornby Q6

Image
With all the rain outside putting a stop to gardening I have been grounded and have used the opportunity to tackle some longstanding issues.  Hornby first released their Q6 models in June 2016.  Having being raised in Middlesbrough I had to take delivery of two versions, an Early Emblem and one with a Late Crest.  They were tested and given a run around the layout before being stored away to make room for some BR (WR) trains. Q6 63443 Hornby R3425 February 2018 and Hornby released a further Early Emblem version.  I dug out my two original models and ran all three together.  It soon became obvious that one of the first models, number 63443, was a much slower runner.  On handling the model I was shocked to realise just how hot the bodyshell had become around the motor.  With further running I could well imagine melting the smokebox. Some research showed a problem with Hornby motors of a similar vintage.  My engine was too old to return for a ...
Read more